Appendix B. Material Constants
Approximate room-temperature values of the photonic materials in this tutorial, and the constants its calculations use.
These are typical values for orientation. Film properties depend on how the material is deposited or grown, so check the cited sources and your PDK before designing.
Optical and electronic properties
Table B.1. Photonic materials near 1550 nm.
| Material | Index at 1550 nm | Band gap | Notes |
|---|---|---|---|
| Silicon (Si) | 3.48 | 1.12 eV, indirect | two-photon absorption at 1550 nm; no Pockels effect |
| Silica (SiO₂) | 1.44 | ≈ 9 eV | cladding and buried oxide |
| Silicon nitride (Si₃N₄, LPCVD) | ≈ 2.0 | ≈ 5 eV | transparent from the visible to the mid-infrared |
| Lithium niobate (LiNbO₃) | no ≈ 2.21, ne ≈ 2.14 | ≈ 4 eV | Pockels r33 ≈ 31 pm/V [32] |
| Barium titanate (BaTiO₃) | ≈ 2.3 | ≈ 3.2 eV | thin-film Pockels coefficients of hundreds of pm/V [33] |
| Indium phosphide (InP) | 3.17 | 1.34 eV, direct | substrate for 1310 and 1550 nm lasers |
| Gallium arsenide (GaAs) | 3.37 | 1.42 eV, direct | substrate for quantum-dot lasers |
| Germanium (Ge) | ≈ 4.3 | 0.66 eV indirect, 0.80 eV direct | absorbs through the C band: photodetectors |
| Water | 1.318 | the analyte medium of Chapter 34 |
Dispersion models
The figure scripts in figsrc/ use these published Sellmeier fits:
Table B.2. Sellmeier models used for the computed numbers.
| Material | Model | Source |
|---|---|---|
| Silicon | \(n^2 = 11.6858 + \frac{0.939816}{\lambda^2} + \frac{0.00810461\,\lambda_1^2}{\lambda^2 - \lambda_1^2}\), \(\lambda_1 = 1.1071\) µm | Li [59] |
| Fused silica | three-term Sellmeier (0.6961663, 0.4079426, 0.8974794; 0.0684043, 0.1162414, 9.896161 µm) | Malitson [58] |
| Silicon nitride | two-term Sellmeier for LPCVD films | Luke et al. [60] |
| Lithium niobate | extraordinary and ordinary Sellmeier fits | Zelmon et al. [61] |
Thermal and thermo-optic properties
Table B.3. Thermo-optic and thermal constants (room temperature). The thermal conductivities and heat capacities are those of the heater model of Chapter 18.
| Material | dn/dT (1/K) | Thermal conductivity (W/m·K) | Volumetric heat capacity (J/m³·K) |
|---|---|---|---|
| Silicon | 1.8 × 10⁻⁴ | 148 (bulk) | 1.63 × 10⁶ |
| Silica | 1 × 10⁻⁵ | 1.38 | 1.60 × 10⁶ |
| Silicon nitride | 2.5 × 10⁻⁵ | 20–30 (film) | ≈ 2 × 10⁶ |
| TiN (heater) | 28 (film) | 2.85 × 10⁶ | |
| Air | 0.026 | 1.2 × 10³ | |
| Waveguide (500 × 220 nm Si strip, femwell) | dneff/dT = 2.0 × 10⁻⁴ |
Silicon as an electro-optic and nonlinear material
Table B.4. Silicon at 1550 nm.
| Quantity | Value | Chapter |
|---|---|---|
| Plasma dispersion, electrons | Δn = −8.8 × 10⁻²² ΔN, Δα = 8.5 × 10⁻¹⁸ ΔN cm⁻¹ | 19 [40] |
| Plasma dispersion, holes | Δn = −8.5 × 10⁻¹⁸ ΔP0.8, Δα = 6.0 × 10⁻¹⁸ ΔP cm⁻¹ | 19 |
| Relative permittivity (DC) | 11.7 | 19 |
| Intrinsic carrier density | 1.0 × 10¹⁰ cm⁻³ | 19 |
| Kerr coefficient n2 | ≈ 6 × 10⁻¹⁸ m²/W (SiN ≈ 2.5 × 10⁻¹⁹) | 7 |
| Two-photon absorption βTPA | 0.5–1 cm/GW | 7 |
| Radiative recombination B | ≈ 10⁻¹⁴ cm³/s (InGaAsP ≈ 10⁻¹⁰) | 22 |
III–V gain material
Table B.5. Parameters of the laser models (InGaAsP-like, 1550 nm). Illustrative textbook values, used consistently in Chapters 23–25.
| Quantity | Value |
|---|---|
| Electron and hole effective masses | 0.045 m₀ and 0.46 m₀ |
| Kane energy Ep | 25 eV |
| Band-gap temperature coefficient | −0.35 meV/K (about +0.5 nm/K) |
| Recombination coefficients A, B, C | 10⁸ s⁻¹, 10⁻¹⁰ cm³/s, 3 × 10⁻²⁹ cm⁶/s |
| Transparency density (bulk model) | 1.3 × 10¹⁸ cm⁻³ |
| Differential gain (bulk model, 3 × 10¹⁸ cm⁻³) | 4.7 × 10⁻¹⁶ cm² |
| Logarithmic gain fit (laser demo) | g = 1500 cm⁻¹ · ln(N / 2 × 10¹⁸ cm⁻³) |
| Gain compression ε | 2 × 10⁻¹⁷ cm³ |
| Characteristic temperature T₀ | ≈ 60 K |
| Germanium saturation velocity | ≈ 6 × 10⁶ cm/s (photodiode transit time) |
Physical constants
| Constant | Value |
|---|---|
| Speed of light c | 2.998 × 10⁸ m/s |
| Planck constant h | 6.626 × 10⁻³⁴ J·s |
| Elementary charge q | 1.602 × 10⁻¹⁹ C |
| Boltzmann constant k | 1.381 × 10⁻²³ J/K (kT = 25.9 meV at 300 K) |
| Vacuum permittivity ε₀ | 8.854 × 10⁻¹² F/m |
| Electron mass m₀ | 9.109 × 10⁻³¹ kg |