Chapter 14WDM Filters and Polarisation Management
Wavelength-division multiplexing puts many channels on one waveguide, and polarisation devices deal with fibres that scramble polarisation.
- name the WDM grids and what a multiplexer must achieve on them;
- design a ring demultiplexer: free spectral range, bandwidth and crosstalk;
- compare ring rows, MZI lattices, arrayed-waveguide and echelle gratings, and contra-directional couplers;
- explain how polarisation splitters and rotators work;
- describe polarisation-diversity receivers.
How do you separate the four wavelengths of the reference link with low crosstalk?
14.1WDM grids and requirements
Wavelength channels follow standard grids. CWDM spaces them 20 nm apart (for example 1271, 1291, 1311 and 1331 nm in four-channel data-centre transceivers), loose enough for uncooled lasers and simple filters. LAN-WDM uses 800 GHz (about 4.5 nm) spacing near 1310 nm. DWDM uses the ITU frequency grid with 100, 50 GHz or finer spacing in the C band [56]; the reference link uses its 400 GHz (3.2 nm) slots (Chapter 1). A multiplexer or demultiplexer must pass each channel with low insertion loss and a flat enough passband for the signal (about 50 GHz wide at 50 Gb/s), reject its neighbours (crosstalk below about −20 dB), and stay on its channel over temperature.
14.2Ring and MZI-lattice multiplexers
A row of add-drop rings on one bus, each tuned to one channel, is the most compact demultiplexer (Chapter 12). Each ring drops its channel and passes the others; heaters hold each ring on its channel. A single ring has a Lorentzian drop response,
\[T_\mathrm{drop}(\Delta\lambda) = \frac{T_0}{1 + (2\Delta\lambda/\Delta\lambda_\mathrm{FWHM})^2},\]which fixes the trade between passband and crosstalk.
Free spectral range. For a cyclic four-channel demultiplexer the rings’ FSR should be four channel spacings, \(4 \times 3.2 = 12.8\) nm, so that each ring’s next resonance falls one full set of channels away. With \(n_g = 4.18\), \(L = \lambda^2/(n_g\,\mathrm{FSR}) = 2.4025/(4.18 \times 0.0128) = 44.9\) µm: a radius of 7.2 µm.
Bandwidth and crosstalk. For −20 dB of rejection of the neighbouring channel 3.2 nm away, \((2 \times 3.2/\Delta\lambda_\mathrm{FWHM})^2 = 99\), so \(\Delta\lambda_\mathrm{FWHM} \le 0.64\) nm, a loaded Q of about 2400. A 50 Gb/s NRZ signal occupies about 0.4 nm, so a 0.6 nm passband passes it with little filtering penalty. Such a low Q means a strongly over-coupled ring with small gaps (Chapter 9), which also keeps the drop loss low.
The Lorentzian’s slow roll-off is the weakness of single rings. Second- and higher-order filters (two or more coupled rings) give flat tops and much steeper skirts. MZI lattices (Chapter 11) do the same with cascaded interferometers: an interleaver splits odd and even channels, and a tree of them separates many.
14.3Arrayed-waveguide and echelle gratings
For many channels, dispersive devices scale better. An arrayed-waveguide grating (AWG) splits the light in a free-propagation region into an array of waveguides whose lengths increase in equal steps; at the far side they interfere like a diffraction grating, and each wavelength focuses onto a different output waveguide [3]. An echelle grating does the same with an etched reflective grating in a slab. Both demultiplex tens of channels in one device, with passive, flat-ish passbands, but they are larger than rings and sensitive to phase errors in silicon’s high-contrast waveguides, which raise crosstalk.
14.4Crosstalk, flat-top responses and tuning
In practice a demultiplexer’s crosstalk is set less by its ideal response than by imperfections: phase errors in AWGs, side lobes, backscatter in rings and the thermal drift of every resonant device. Ring-based WDM therefore depends on control: each ring needs a heater and a monitor (a photodiode tap or the drop signal itself) in a feedback loop that keeps it locked to its laser line (Chapter 18). Because silicon rings drift by 70–80 pm/K, a 50 K range moves them by more than one 3.2 nm channel; schemes that let each ring lock to whichever channel is nearest, then reassign channels in the electronics, save heater power.
14.5Polarisation splitters and rotators
A silicon strip is strongly birefringent (Chapter 6), and grating couplers accept one polarisation only, but light arriving from a standard fibre has an unknown, drifting polarisation (Chapter 2). Two devices handle it:
- Polarisation splitters separate TE and TM. A common design is an asymmetric directional coupler phase-matched for TM but not TE: TM crosses to the second waveguide while TE stays.
- Polarisation rotators turn TM into TE. In silicon the usual trick uses mode hybridisation: in a waveguide with a vertically asymmetric cross-section (a partial etch or a different upper cladding), the TM0 mode and the TE1 mode exchange character along an adiabatic taper, so TM0 becomes TE1; an asymmetric coupler then converts TE1 in the wide guide into TE0 in a narrow one (Chapter 8). Together this is a polarisation splitter-rotator (PSR).
14.6Polarisation diversity
A polarisation-diversity receiver splits the incoming light into its two polarisations, rotates one, and processes both copies on identical TE circuits, adding the detected signals at the end. A two-dimensional grating coupler does the splitting and rotation in one step: it couples the two fibre polarisations into two orthogonal TE waveguides. The cost is a doubled circuit and the need for the two paths to match.
Ring demultiplexer: four add-drop rings of about 7.2 µm radius (FSR 12.8 nm), over-coupled to a loaded Q of about 2400 (0.64 nm passband) for −20 dB adjacent-channel rejection, each with a heater and a locking loop. TE only; the receiver uses a TE grating coupler and polarisation-maintaining fibre in the lab.
Reading
- [3] Katsunari Okamoto. Fundamentals of Optical Waveguides, 3rd edition. Academic Press, 2021.
- [1] Lukas Chrostowski and Michael Hochberg. Silicon Photonics Design: From Devices to Systems. Cambridge University Press, 2015. https://www.cambridge.org/core/books/silicon-photonics-design/BF3CF13E8542BCE67FD2BBC7104ECEAB
- [35] Wim Bogaerts et al. “Silicon microring resonators.” Laser & Photonics Reviews, 6(1):47–73, 2012.
- [56] ITU-T. Recommendation G.694.1: Spectral grids for WDM applications: DWDM frequency grid. International Telecommunication Union.
- WDM grids: CWDM (20 nm), LAN-WDM (800 GHz), DWDM (ITU grid, 400 GHz to 50 GHz and below).
- A four-channel ring demultiplexer on a 3.2 nm grid needs rings of FSR 12.8 nm (R ≈ 7.2 µm) and a loaded Q of about 2400 for −20 dB crosstalk.
- Higher-order rings and MZI lattices flatten the passband and sharpen the skirts; AWGs and echelles scale to many channels.
- Every resonant demultiplexer needs heaters and locking loops against thermal drift.
- Polarisation splitter-rotators and 2D grating couplers make silicon circuits work with fibre’s arbitrary polarisation.