Course Map

The whole tutorial on one page: every part, chapter and section, and the interactive demos. Built demos are marked ●, planned ones ○.

Part I · Foundations

Light as an electromagnetic wave, the Gaussian beams and fibres that carry it to a chip, and the materials (silicon, silicon nitride, lithium niobate, barium titanate, indium phosphide) that photonic chips are made of.

1. Why Integrated Photonics?

When does light beat copper, and what does a photonic chip need to do it?

1.1 Light versus charge · 1.2 Applications · 1.3 Why silicon, and why not only silicon · 1.4 Anatomy of a photonic integrated circuit · 1.5 Optical power and decibels · 1.6 The two running examples · 1.7 How to use this tutorial

Demos: ● Power budget

2. Electromagnetic Theory for Photonics

What does light do at an interface, and how does that lead to confinement?

2.1 Maxwell’s equations in matter · 2.2 The wave equation and plane waves · 2.3 Refractive index, absorption and dispersion · 2.4 Polarisation and power · 2.5 Reflection and refraction · 2.6 Total internal reflection and evanescent waves · 2.7 Phase velocity, group velocity and group index

Demos: ● Polarisation ellipse; ● Snell, Fresnel and total internal reflection; ● Wave packet

3. Gaussian Beams and Optical Fibres

How much light gets from one Gaussian mode into another?

3.1 The paraxial wave equation · 3.2 The Gaussian beam · 3.3 Beam transformation with q and ABCD · 3.4 Optical fibres · 3.5 Mode overlap and coupling efficiency · 3.6 Gaussian beams in photonic chips

Demos: ● Gaussian beam and lens; ● Fibre modes

4. Materials and Platforms: Si, SiN, TFLN, BTO and InP

Which platform for which job?

4.1 What a platform must provide · 4.2 The materials · 4.3 Silicon-on-insulator · 4.4 Silicon nitride · 4.5 Thin-film lithium niobate · 4.6 Barium titanate · 4.7 Indium phosphide and other III–Vs · 4.8 Choosing and combining platforms

Demos: ● Platform comparator

Part II · Waveguides

How a strip of high-index material guides light: slab and channel waveguides on SOI and other platforms, the losses that limit them, and the bends, tapers and transitions that route light around a chip.

5. The Slab Waveguide

What sets the number of guided modes and their effective index?

5.1 The ray picture and transverse resonance · 5.2 TE and TM modes · 5.3 Effective index and normalised parameters · 5.4 Cut-off and the single-mode condition · 5.5 Confinement and the evanescent field · 5.6 Group index of a slab mode

Demos: ● Slab-waveguide mode solver

6. Channel Waveguides on SOI and Beyond

Which width and etch depth give single-mode, low-loss, compact routing?

6.1 Geometries · 6.2 The effective-index method · 6.3 Numerical mode solvers · 6.4 Effective and group index of SOI waveguides · 6.5 Single-mode conditions and polarisation · 6.6 Other platforms · 6.7 Sensitivity to fabrication

Demos: ● Effective-index explorer; ○ 2D mode solver

7. Loss, Dispersion and Nonlinearity

What limits a waveguide’s propagation loss, and how do you measure it?

7.1 Loss mechanisms and units · 7.2 Sidewall-roughness scattering · 7.3 Absorption · 7.4 Substrate leakage · 7.5 Dispersion · 7.6 Nonlinear effects · 7.7 Measuring loss

Demos: ● Cutback simulator; ○ Roughness scattering

8. Bends, Tapers and Transitions

How tight can a bend be, and how short a taper?

8.1 Radiation loss in bends · 8.2 Mode mismatch at straight–bend junctions · 8.3 Tapers and adiabaticity · 8.4 Overlap integrals and butt coupling · 8.5 Waveguide crossings · 8.6 Transitions between layers

Demos: ● Circular and Euler bends; ○ Taper adiabaticity

Part III · Passive Devices

The building blocks that split, combine, filter and route light without power: directional couplers, Y-branches and MMIs, Mach–Zehnder interferometers, ring resonators, Bragg gratings, and WDM and polarisation devices.

9. Coupled-Mode Theory and Directional Couplers

Which length and gap give a 50/50 split, and how robust is it?

9.1 Coupled-mode equations · 9.2 Supermodes · 9.3 The directional coupler · 9.4 Wavelength, polarisation and fabrication sensitivity · 9.5 Broadband and adiabatic couplers · 9.6 The 2 × 2 scattering matrix

Demos: ● Directional coupler

10. Y-Branches and Multimode Interference Couplers

Y-branch or MMI, and how long must the MMI be?

10.1 Y-branches · 10.2 Mode excitation at an abrupt junction · 10.3 Self-imaging in a multimode waveguide · 10.4 MMI design · 10.5 Comparing splitters

Demos: ● MMI self-imaging

11. Mach–Zehnder Interferometers

How does the arm-length difference set the spectrum?

11.1 Interference and optical phase · 11.2 The MZI transfer function · 11.3 Unbalanced MZIs · 11.4 Tuning · 11.5 Cascaded and lattice filters · 11.6 MZIs as test structures

Demos: ● Mach–Zehnder interferometer

12. Ring Resonators

How do coupling and loss shape a ring’s resonance?

12.1 Resonance condition · 12.2 The all-pass ring · 12.3 The add-drop ring · 12.4 Quality factor and finesse · 12.5 Extracting parameters from measurements · 12.6 Non-idealities · 12.7 Applications

Demos: ● Ring resonator

13. Bragg Gratings and Photonic Crystals

How long and how strong must a grating be for a given reflectivity and bandwidth?

13.1 Periodic waveguides and the Bragg condition · 13.2 Coupled-mode theory of gratings · 13.3 The transfer-matrix method · 13.4 Apodisation and chirp · 13.5 Cavities · 13.6 Contra-directional couplers and SWG metamaterials · 13.7 Photonic crystals

Demos: ● Bragg grating

14. WDM Filters and Polarisation Management

How do you separate four wavelengths with low crosstalk?

14.1 WDM grids and requirements · 14.2 Ring and MZI-lattice multiplexers · 14.3 Arrayed-waveguide and echelle gratings · 14.4 Crosstalk, flat-top responses and tuning · 14.5 Polarisation splitters and rotators · 14.6 Polarisation diversity

Demos: ○ Four-channel demultiplexer

Part IV · Coupling and Packaging

Getting light on and off the chip: grating couplers, edge couplers, fibre arrays, photonic wire bonds and the packaging that turns a die into a product.

15. Grating Couplers

Which period and angle couple 1550 nm TE light into a fibre tilted at 8°, and how much of the light can you expect to get?

15.1 Phase matching · 15.2 Directionality · 15.3 Mode matching to the fibre · 15.4 Bandwidth and polarisation · 15.5 Back-reflection · 15.6 Focusing, SWG and 2D grating couplers · 15.7 Grating couplers in practice

Demos: ● Grating-coupler phase matching · ● Grating-coupler efficiency budget

16. Edge Couplers and Spot-Size Converters

How narrow must the taper tip be to match a 3 µm or a 10 µm spot?

16.1 Edge-coupling basics · 16.2 Inverse tapers · 16.3 Multi-stage couplers and overlays · 16.4 Facets · 16.5 Fibres at the edge · 16.6 Edge against grating couplers

Demos: ● Inverse-taper edge coupler

17. Fibre Arrays, Photonic Wire Bonds and Packaging

How tolerant is a coupling interface, and how do you find the peak quickly?

17.1 Fibre arrays · 17.2 Alignment · 17.3 Attaching fibres · 17.4 Photonic wire bonds and micro-optics · 17.5 Laser and chip assembly · 17.6 Co-packaged optics · 17.7 Design rules for test and packaging

Demos: ● Alignment tolerance · ● Fibre-array alignment

Part V · Active Devices

Tuning, modulating and detecting light: thermo-optic phase shifters, electro-optic effects in each platform, modulators, and germanium photodetectors and receivers.

18. Thermo-Optic Phase Shifters

How many milliwatts for a π shift, and how fast?

18.1 The thermo-optic effect · 18.2 Heater types · 18.3 Thermal circuits · 18.4 Improving efficiency · 18.5 Crosstalk and stabilisation

Demos: ● Thermo-optic phase shifter · ● Ring locking

19. Electro-Optic Effects Across Platforms

Which effect gives the best VπL for a given loss and bandwidth?

19.1 Free-carrier plasma dispersion · 19.2 PN, PIN and MOS structures · 19.3 The Pockels effect · 19.4 Electro-absorption · 19.5 Figures of merit

Demos: ● PN depletion phase shifter

20. Modulators

Mach–Zehnder or ring modulator for a four-wavelength link?

20.1 Modulator metrics · 20.2 Mach–Zehnder modulators · 20.3 Ring modulators · 20.4 Electro-absorption modulators · 20.5 TFLN and BTO modulators · 20.6 Modulation formats · 20.7 Driver and modulator co-design · 20.8 Ring-modulator dynamics · 20.9 Driving, linearising and locking a ring

Demos: ● MZM and eye diagram · ● Ring modulator

21. Photodetectors and Receivers

How much optical power does the receiver need for a target BER?

21.1 Absorption and responsivity · 21.2 Germanium-on-silicon photodiodes · 21.3 Bandwidth · 21.4 Dark current and noise · 21.5 Avalanche photodiodes · 21.6 Receivers · 21.7 Monitor photodiodes · 21.8 Designing the receiver front end, step by step · 21.9 Equalisation, clock recovery and measuring sensitivity

Demos: ● Photodiode bandwidth · ● Receiver sensitivity

Part VI · Lasers and Amplifiers

From the physics of gain to working lasers: emission and gain in semiconductors, the Fabry–Pérot laser and its rate equations, noise and linewidth, tunable and narrow-linewidth lasers, lasers on silicon, and semiconductor optical amplifiers.

22. Light Meets Matter: Absorption, Emission and Gain

What does it take for a material to amplify light?

22.1 Photons and energy levels · 22.2 Absorption and emission · 22.3 Population inversion and gain · 22.4 Lineshape and gain spectrum · 22.5 Direct and indirect bandgaps

Demos: ● Level-system model

23. Semiconductor Gain Media

How many carriers does it take to reach gain, and where is the gain peak?

23.1 Bands, density of states and occupation · 23.2 Quasi-Fermi levels and the condition for gain · 23.3 The gain spectrum · 23.4 Heterostructures, quantum wells and quantum dots · 23.5 Material systems for 1310 and 1550 nm · 23.6 Recombination

Demos: ● Gain spectrum

24. The Fabry–Pérot Laser and the Rate Equations

What sets a laser’s threshold current and slope efficiency?

24.1 The optical cavity · 24.2 Threshold · 24.3 Rate equations · 24.4 The L–I curve and efficiency · 24.5 Temperature · 24.6 Transients · 24.7 The Fabry–Pérot spectrum · 24.8 The vertical-cavity surface-emitting laser

Demos: ● Laser rate equations

25. Laser Dynamics, Noise and Linewidth

How fast can you modulate a laser directly, and how narrow is its line?

25.1 Small-signal modulation · 25.2 Chirp and the α-factor · 25.3 Relative intensity noise · 25.4 Phase noise and linewidth · 25.5 Optical feedback · 25.6 Narrowing the linewidth · 25.7 Driving a laser: bias, modulation and extinction ratio · 25.8 The laser as a circuit, and equalisation · 25.9 Output stages and temperature control

Demos: ● Modulation response, RIN and linewidth

26. Single-Frequency and Tunable Lasers

How do two rings select one lasing mode over a 40 nm range?

26.1 Why single-frequency · 26.2 DFB lasers · 26.3 DBR lasers and tuning · 26.4 External-cavity lasers on Si and SiN · 26.5 The Vernier effect · 26.6 Self-injection locking · 26.7 Multi-wavelength sources

Demos: ● Vernier ring laser

27. Lasers on Silicon

Which integration approach for which volume and performance?

27.1 Why the light source is the hard part · 27.2 External and flip-chip lasers · 27.3 Heterogeneous integration · 27.4 Micro-transfer printing · 27.5 Monolithic growth · 27.6 Thermal and reliability · 27.7 Open laser-integration projects · 27.8 Directly modulated microring lasers

Demos: ● III–V/Si supermodes

28. Semiconductor Optical Amplifiers

How much gain, at what output power and noise figure?

28.1 From laser to amplifier · 28.2 Gain and saturation · 28.3 Noise figure · 28.4 Dynamics and patterning · 28.5 Polarisation and reflections · 28.6 SOAs in photonic circuits · 28.7 Erbium and other amplifiers

Demos: ● SOA gain and noise figure

Part VII · Fabrication, Testing and Data Analysis

How photonic chips are made and verified: fabrication and its variations, the design flow and open PDKs, test setups and data analysis.

29. Fabrication

How do nanometre variations turn into nanometre wavelength shifts?

29.1 SOI wafers · 29.2 Lithography · 29.3 Etching and cladding · 29.4 Doping, metals and germanium · 29.5 Other platforms · 29.6 Process variation · 29.7 Design for manufacturing · 29.8 Access

Demos: ● Wafer-map Monte Carlo

30. Design Flow and Open PDKs

What happens between a simulation and a manufacturable layout?

30.1 The design flow · 30.2 Process design kits · 30.3 Layout with KLayout and SiEPIC-Tools · 30.4 Layout as code with gdsfactory · 30.5 Component simulation · 30.6 Circuit simulation · 30.7 Verification · 30.8 Tape-out through openEBL

Demos: ● Circuit simulator

31. Testing Photonic Chips

How do you trust a measured spectrum?

31.1 The passive test setup · 31.2 Automated testing and design for test · 31.3 Calibration and de-embedding · 31.4 Testing active devices · 31.5 Testing lasers · 31.6 High-speed testing · 31.7 Wafer-scale testing

Demos: ● Virtual test bench

32. Data Analysis

How do you extract physical parameters, with error bars, from measured spectra?

32.1 Data formats and open datasets · 32.2 Calibrating out the grating couplers · 32.3 Propagation loss by cutback · 32.4 Group index from interferometers and rings · 32.5 Fitting ring resonances · 32.6 Bragg-grating parameters · 32.7 Statistics across a wafer · 32.8 Back to compact models

Demos: ● Ring-fit playground

Part VIII · Systems and Applications

Everything together: optical links and transceivers, and the sensing, LiDAR, quantum and computing systems built from the same blocks.

Does the reference link close, and what does each block contribute?

33.1 Link architectures · 33.2 Power budget and penalties · 33.3 WDM transceivers · 33.4 Coherent transceivers · 33.5 Energy per bit · 33.6 Co-packaged optics · 33.7 The reference link, block by block · 33.8 NRZ or PAM4 · 33.9 Drivers and equalisation · 33.10 Clocking, jitter and the timing budget · 33.11 Optimising for energy

Demos: ● Link budget

34. Beyond Datacom: Sensing, LiDAR, Quantum and Computing

What changes when the chip is a sensor, a beam steerer or a processor instead of a transceiver?

34.1 Biosensing with evanescent fields · 34.2 LiDAR and optical phased arrays · 34.3 Quantum photonics · 34.4 Photonic computing · 34.5 Microwave photonics and frequency combs · 34.6 Visible and mid-infrared photonics

Demos: ● Ring biosensor · ● Optical phased array

Hands-On Labs

Twelve labs in three tracks, using free tools only: simulate (mode solvers, FDTD, circuit models), make (lay out, verify and submit an openEBL chip, then analyse its measurements), and lasers and links (rate equations, a Vernier laser, the reference-link budget). See the labs page.


Back to top

Open-Photonics, draft v0.1 (November 2026) · Source on GitHub

This tutorial is being written with the help of AI tools and may contain mistakes. If you find one, please open an issue, and we will correct it. Text and figures CC BY 4.0, code MIT; third-party PDK devices keep their own licences and credits.